Guides Apple Home sensor automations: motion, presence, temperature & humidity
Sensor automations in Apple Home
A smart home gets useful at the moment a sensor flips the switch instead of your thumb. This guide covers which sensors Apple Home can trigger on natively, which need a third-party app, and how to build rules that do not misfire at 3 a.m.
What Apple Home can trigger on
The Home app's built-in “A Sensor Detects Something” automation only covers a fixed list of accessory types. Anything outside that list shows up as a reading on the tile, but is not usable as a trigger.
| Sensor type | Native trigger | Typical use |
|---|---|---|
| Motion | Yes | Hallway light, alarm |
| Contact (door / window) | Yes | “Door opened while nobody is home” |
| Smoke / CO | Yes | Alert plus lights on |
| Water leak | Yes | Alert, shut-off valve |
| Light level | Yes | Lights only when it is actually dark |
| Occupancy (mmWave radar) | Usually exposed as motion | Room-level presence |
| Temperature | No | Needs a third-party automation app |
| Humidity | No | Needs a third-party automation app |
| Air quality | No | Vendor app or third-party automation app |
Temperature and humidity: the honest limitation
Apple Home displays temperature and humidity on the accessory tile and in widgets, but the built-in automation editor does not offer a “temperature above / below” trigger. To automate on those numbers you need a HomeKit automation app that can create the rule for you — Eve, Controller for HomeKit and Home+ are the usual three.
Those rules still execute on your Apple home hub, not on the iPhone, so a hub is required either way. Use the vendor app only to set thresholds, then forget it exists.
Rules people actually build this way:
- Bathroom fan on above ~65% humidity, off below ~55%.
- “Window left open” warning when indoor temperature drops several degrees in 15 minutes.
- Heater cut-off above 25°C in a child's room.
- Dehumidifier on when the basement sensor stays above 60% for an hour.
Three kinds of presence — pick deliberately
1. iPhone geofence
“When I Arrive”, “When I Leave”, “When the First Person Arrives”, “When the Last Person Leaves”. These depend on iPhones, so every household member has to share the home and grant location access. The first/last variants are the useful ones — and they need a home hub to fire reliably while nobody is in the house.
2. PIR motion
Classic passive infrared: cheap, battery-friendly, fast. It detects movement, so it drops you the moment you sit still, and it reacts to pets and sunbeams. Perfect for “light on when someone walks past”, poor for “is anyone in the office”.
3. mmWave presence
Radar-based: detects a person who is present but still — desk work, sofa, bathroom. It holds state longer and reacts faster, at the cost of price, power (often wired or frequently charged), and a tendency to see through thin walls when mounted carelessly. In Apple Home these usually surface as motion or occupancy sensors, while zones and sensitivity live in the maker's app.
Build automations that do not misfire
- Give the “off” a delay. Use the built-in duration (“turn off after 5 minutes”) instead of a second automation triggered by “no motion detected”. Two opposing rules are the classic cause of flickering lights.
- Use conditions, not more automations. “Only at night” and “Only when nobody is home” belong in the condition section of the same rule.
- One owner per light. A motion rule and a manual switch rule will fight. Decide which wins and disable the other.
- Tune sensitivity in the vendor app. Pet immunity, zone masks and cooldowns are not exposed in Apple Home.
- Watch a week of history first. Never put a lock, heater or alarm behind an untested trigger.
- Keep the Thread mesh healthy. Mains-powered Thread devices strengthen the network that battery sensors depend on — see Thread border router.
Five automations worth building
| Automation | Trigger | Condition | Action |
|---|---|---|---|
| Hallway light | Motion | After sunset | On at 40%, off after 3 min |
| Away alert | Contact sensor opens | Nobody home | Notification, lights on |
| Bathroom fan | Humidity above 65% (third-party app) | — | Fan on, off below 55% |
| Frost warning | Temperature below 17°C (third-party app) | Heating season | Notification |
| Night light | Motion | 23:00–06:00 | 5% warm white |
Pick sensors by protocol, not by brand
- Eve Motion (Matter) — Matter over Thread, and it also reports light level, so “only when dark” works with one device.
- Aqara Presence Sensor FP2 — Wi-Fi mmWave presence sensor listed for Apple Home; Aqara documents zone-based detection in its own app.
- Meross Presence Sensor MS605 — battery mmWave, Matter over Thread, IP67.
- Onvis Smart Motion Sensor SMS2 — HomeKit over Thread; its product listing also advertises temperature and humidity, which is what the third-party-app rules above need.
- Qingping Thermometer & Hygrometer — HomeKit temperature/humidity sensor for threshold rules.
Battery sensors are almost always Thread, and Thread needs a border router. Every protocol per device is in the matrix; the ranked shortlist is on best sensors for Apple Home, and the full list is in the sensor category. New to automations in general? Start with Apple Home automations.
FAQ
Can Apple Home automate on temperature?
Not with the built-in automation editor — it offers no temperature or humidity threshold trigger. You need a third-party HomeKit automation app such as Eve, Controller for HomeKit or Home+, which can create those rules. They still run on an Apple home hub.
Do sensor automations work without a home hub?
No. Automations that run while you are away need an Apple home hub (HomePod or Apple TV) to execute them. Without one, rules only fire while your iPhone is at home.
What is the difference between motion and presence sensors?
A PIR motion sensor detects movement, so it stops reporting when a person sits still. An mmWave presence sensor detects a person who is present but motionless, which makes it better for offices, sofas and bathrooms.
Why does my motion automation turn the light off while I am still in the room?
Because PIR sensors report “no motion” when you stop moving. Use a presence sensor, extend the turn-off delay, or add a condition so the light only turns off when the room has been empty for several minutes.
Do I need a Thread border router for battery sensors?
For Matter-over-Thread sensors, yes — a HomePod mini, HomePod (2nd gen) or Apple TV 4K (2nd/3rd gen) provides it. Wi-Fi and Bluetooth sensors do not need one, but Bluetooth sensors only work in range.